TX16S flash from bootloader stuck @ 80/90%

[Ga1j1n]

Is there an existing issue for this problem?

• I have searched the existing issues

What part of EdgeTX is the focus of this bug?

Transmitter firmware

Current Behavior

Updated from 2.10.1 to 2.10.2 via the bootloader flasher (also updated first along with SD) it seems the flash has stuck at approx 90%, how long do I wait?, normally it's very quick, Suspect I'll brick it if I interrupt

Expected Behavior

Standard flash behaviour, flashed this way many times

Steps To Reproduce

1. left right trims in and power on to enter bootloader 2) select firmware file 3) select flash 4) lockup

Version

2.10.2

Transmitter

RadioMaster TX16S / TX16SMK2

Operating System (OS)

Windows

OS Version

Not applicable

Anything else?

No response

[Ga1j1n]

recovered using STM32Cube Programmer, hopefully isolated
https://www.youtube.com/watch?v=H9_sxXY_K-8

[Merga189]

Interesting. Which bootloader version did you use? I see here an issue with the bootloader version 2.10.x on my X10S express.

#5250

Reverting to bootloader 2.9.4 and it works fine here.

br Karl

[pfeerick]

This is not new to 2.10, but has been happening every so often since 2.5- 2.6 or maybe since day 1. It is recoverable on handset simply by removing the battery, reconnecting it, and doing the firmware update again. You can't brick the radio by interrupting, as only the firmware is being written, not the bootloader.

…

On Sat, 6 July 2024, 12:33 am Karl, ***@***.***> wrote: Interesting. Which bootloader version did you use? I see here an issue with the bootloader version 2.10.x on my X10S express. #5250 <#5250> Reverting to bootloader 2.9.4 and it works fine here. br Karl — Reply to this email directly, view it on GitHub <#5251 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ABJ66KM67FYBPJANF75HZ53ZK2VC5AVCNFSM6AAAAABKNHOYMGVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDEMJQHE4DMMZZGY> . You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

[Ga1j1n]

This was with bootloader 2.10.2

[3djc]

It is a random event, already existed in otx

[dirteat]

Sorry to add to the fest that updating from 2.9.0 to 2.10.5 today, did the same for me. Bootloader writing failed around 80% forever. And yes, after a while I removed the battery and it is bricked :(

TX16 Mark II

[pfeerick]

This comment still applies. It will not be bricked... you should still be able to re-enter the bootloader, just not the main firmware since that obviously did not finish writing.
#5251 (comment)

And if for some reason it still won't let you into the bootloader, you can use EdgeTX Buddy in DFU mode to update via USB.

[dirteat]

Maybe I misunderstood how to enter the bootloader, but it is not booting anymore, cannot start again the firmware update even pressing T1/T4 + power. Nothing... And I've been spending 3 hours now trying to download the superb STM32CubeProgrammer on that very special website...

[pfeerick]

No, that is the correct way... Ok, something really strange going on there. Did you update the bootloader before trying to update the firmware?

Do you need to download STM32CubeProgrammer (i.e. do you need it for the driver? If you are running a chrome based web browser, you may be able to do the firmware update online, unless you are unlucky enough that one of the fuse settings on the MCU needs changing.

And yes, the STMicro website can sometimes be... Unhelpful... there has been times when it will not let me log in... (making that a job for another day) and others where the download page refuses to give me the link... I just refresh it every few 5-10 minutes, give it plenty of time to think and load, and it usually finally coughes it up.

[dirteat]

Well, I've followed exactly the update instruction with the bootloader method:

https://manual.edgetx.org/installing-and-updating-edgetx/update-from-an-earlier-version-of-edgetx-using-the-bootloader

So, yes, I've first updated the bootloader (navigating the menu etc), which went well, then went on rebooting the radio with T1/T4 pressed, and selected Write Firmware and it hanged out there at 80%. Then, I've removed the battery after a long while and it remained black whatever I do for booting.

The only things I was hesitating too was to either put in FIRMWARE tx16s-6b539d0.bin (from edgeTX repo) or the tx16s-EN-bluetooth-9309ea2.bin, and I did choose the second one. May that was my mistake?

Anyway, I've got the linux version of STM32 (I've spend some time trying to use it under windows7, it is not supported anymore...). Time to play :)