Need help with config

[marcingminski]

Hi Gareth,

Great plugin - thank you! I need some help with the config though. I have set the IP and the port and I can see the connection in the homebridge logs:

[05/11/2020, 18:42:31] [TexecomConnect] Accessory Loaded: Area A
[05/11/2020, 18:42:31] [TexecomConnect] Accessory Loaded: Kitchen
[05/11/2020, 18:42:32] [TexecomConnect] Connected to SmartCom - 192.168.1.142:10001
[05/11/2020, 18:42:40] [TexecomConnect] Reconnecting to SmartCom - 192.168.1.142:10001
[05/11/2020, 18:42:40] [TexecomConnect] Disconnected from SmartCom - 192.168.1.142:10001
[05/11/2020, 18:42:51] [TexecomConnect] Connected to SmartCom - 192.168.1.142:10001
[05/11/2020, 18:43:53] [TexecomConnect] Disconnected from SmartCom - 192.168.1.142:10001

But the status of the alarm in Homebridge keeps saying "Arming" and does not change when I arm or disarm the alarm via normal way - I understand arming/disarming via Homebridge is not supported - fine with that.

I am thinking that maybe I have not set the zones and areas correct. I have access to Wintex and used the same zone IDs and Area names.

Areas:
Name: Area A
ID: 1

Zones:
Name: Kitchen
ID: 11

(just one zone for a test)

Smartcom version: 02.02.02

Any guidance appreciated, I'm also happy to help you with testing/debugging etc if you like.

[garethflowers]

Thanks! Appreciate the help!

Can you try running Homebridge in Debug mode - as this will output a few more extra bits of information in to the logs.

[marcingminski]

I am using Homebridge UI, went to Homebridge Settings and enabled Homebridge Debug Mode -D in the startup options.
There seems to be only one more line output "Socket Data":

[07/11/2020, 19:15:01] Homebridge v1.2.3 is running on port 51556.
[07/11/2020, 19:15:01] [TexecomConnect] Connected to SmartCom - 192.168.1.142:10001
[07/11/2020, 19:15:11] [TexecomConnect] Socket Data: ���
[07/11/2020, 19:15:11] [TexecomConnect] Reconnecting to SmartCom - 192.168.1.142:10001
[07/11/2020, 19:15:11] [TexecomConnect] Disconnected from SmartCom - 192.168.1.142:10001
[07/11/2020, 19:15:21] [TexecomConnect] Connected to SmartCom - 192.168.1.142:10001
[07/11/2020, 19:16:24] [TexecomConnect] Disconnected from SmartCom - 192.168.1.142:10001

Just to prove the point that the connection seems established, if I modify the IP to something else:

[07/11/2020, 19:27:14] [TexecomConnect] Socket Error: Error: connect ECONNREFUSED 192.168.1.143:10001
    at TCPConnectWrap.afterConnect [as oncomplete] (net.js:1146:16) {
  errno: -111,
  code: 'ECONNREFUSED',
  syscall: 'connect',
  address: '192.168.1.143',
  port: 10001
}
[07/11/2020, 19:27:14] [TexecomConnect] Reconnecting to SmartCom - 192.168.1.143:10001
[07/11/2020, 19:27:14] [TexecomConnect] Unable to connect to 192.168.1.143:10001

[erickkowalski]

Hi There

!!!!yes long awaiting possibility to get Texecom system to work with Hombridge

but I seems to have exactly the same problem as marcingminski
the alarm in Homebridge keeps saying "Arming"

Also the door contact nor motion sensor dont change theirs states

Disconnected from SmartCom - 192.168.0.13:10001

Im running the latest smartCom firmware V03.00.16

Any help will be appreciated

cheers Erick

Ps Happy to help with testing

[zebde]

I have the same issue as above with Smartcom version V02.01.05

homebridge          | [11/27/2020, 8:10:09 PM] Registering platform 'homebridge-texecom-connect.TexecomConnect'
homebridge          | [11/27/2020, 8:10:09 PM] [TexecomConnect] Initializing TexecomConnect platform...
homebridge          | [11/27/2020, 8:10:09 PM] [TexecomConnect] Accessory Loaded: House
homebridge          | [11/27/2020, 8:10:09 PM] [TexecomConnect] Accessory Loaded: Kitchen
homebridge          | [11/27/2020, 8:10:10 PM] [TexecomConnect] Accessory Loaded: Front Door
homebridge          | [11/27/2020, 8:10:10 PM] [TexecomConnect] Accessory Loaded: Hallway
homebridge          | [11/27/2020, 8:10:10 PM] [TexecomConnect] Accessory Loaded: Bedroom
homebridge          | [11/27/2020, 8:10:10 PM] [TexecomConnect] Accessory Loaded: Office
homebridge          | [11/27/2020, 8:10:10 PM] [TexecomConnect] Accessory Loaded: Office Door
homebridge          | [11/27/2020, 8:10:10 PM] [TexecomConnect] Accessory Loaded: Garden Door
homebridge          | [11/27/2020, 8:10:10 PM] [TexecomConnect] Connected to SmartCom - 192.168.173.222:10001
homebridge          | [11/27/2020, 8:11:12 PM] [TexecomConnect] Disconnected from SmartCom - 192.168.173.222:10001

[MichaelVdheeren]

Same issue for me as above.

[Rich-Chamberlain]

I am receiving the same results on my set up. I have a SmartCom and a separate COMIP module, both are giving me the same results.

On starting homebridge I get the following on the home app:

Opening of the contact switches or motion does not change the status of the sensors within homebridge.

My test json file can be found below:

"platforms": [
{
"platform": "TexecomConnect",
"host": "192.168.1.2",
"port": 10001,
"areas": [
{
"name": "Area A",
"number": 1,
"accessory": "security"
}
],
"zones": [
{
"accessory": "contact",
"number": 1,
"name": "Front Door"
},
{
"accessory": "contact",
"number": 2,
"name": "Rear Door"
},
{
"accessory": "motion",
"number": 3,
"name": "Hallway"
}
]
}
]

[5xPa]

Good Morning has they issue been resolved I have exactly same problem.

Here is the log showing HomeBridge disconnects from Smartcom

2/18/2021, 1:36:40 PM Loaded plugin 'homebridge-texecom-connect'
2/18/2021, 1:36:40 PM [2/18/2021, 6:36:40 AM] Registering platform 'homebridge-texecom-connect.TexecomConnect'
2/18/2021, 1:36:40 PM Loading 1 platforms...
2/18/2021, 1:36:40 PM [TexecomConnect] Initializing TexecomConnect platform...
2/18/2021, 1:36:40 PM [TexecomConnect] Accessory Loaded: Area B
2/18/2021, 1:36:40 PM [TexecomConnect] Accessory Loaded: Area A
2/18/2021, 1:36:40 PM [TexecomConnect] Accessory Loaded: Living Room
2/18/2021, 1:36:40 PM [TexecomConnect] Accessory Loaded: Front Door
2/18/2021, 1:36:40 PM Bridge is running on port 51826.
2/18/2021, 1:36:40 PM [TexecomConnect] Connected to SmartCom - 192.168.0.7:10001
2/18/2021, 1:37:43 PM [TexecomConnect] Disconnected from SmartCom - 192.168.0.7:10001

Here is my configuration
areas
[
{
"name": "Area A",
"number": 1,
"accessory": "security"
},
{
"name": "Area B",
"number": 2,
"accessory": "security"
}
]
Zones
{
"accessory": "motion",
"number": 18,
"name": "Living Room"
},
{
"accessory": "contact",
"number": 23,
"name": "Front Door"
}
]

The app on iPhone displays Area A and Area B
There is no indication for Zones number 18 Living Room, or Zone 23 Front Door

Hopefully somone can suggest a resoloution. Please note I am an absolute beginner, no experience of coding

[Rich-Chamberlain]

I got mine working by changing the ComIP module protocol to Crestron.

I have a separate COMIP module to the Smartcom which gives me some freedom to tinker without screwing it up.

Make sure you take a backup in wintex of your config before continuing. Good luck.

[erickkowalski]

I got mine working by changing the ComIP module protocol to Crestron.

I have a separate COMIP module to the Smartcom which gives me some freedom to tinker without screwing it up.

Make sure you take a backup in wintex of your config before continuing. Good luck.

Hi Rich

i belive the problem here is to make it work with smartcom only.

Btw do you have your comIp wired to the raspberry via usb/erhernet cable permamently??

Anyone have any ideas how to make it work on smartcom

cheers Erick

[5xPa]

Thanks guys for the reply.

I got mine working by changing the ComIP module protocol to Crestron.

I have a separate COMIP module to the Smartcom which gives me some freedom to tinker without screwing it up.

Make sure you take a backup in wintex of your config before continuing. Good luck.

Ok fired up Wintex Connect to panel via Smartcom
In Comms >> Radio Pad and Comports
On Board Digi Com Nothing Fitted
Com Port 1 Smartcom
Com Port 2 ComIp ... changed to Crestron
Com Port 3 Nothing Fitted

Com IP details
Com 1 radio button selected Local IP addresss ... blank
Com 2 radio button selected Local IP 192.168.0.7 (the ip address added to homebridge-texecom-connect) port 1001
Com 3 radio button selected Local IP addresss ... blank

Now if I open front door or walk past living room sensor I get alerts on my phone.
Yet in HomeKit I don't see motion sensor or contact.

Maybe I have messed up Homebridge, in HomeKit

Thanks for the assistance now I need to figure out why the sensor don't show up

[5xPa]

To Rich-Chamberlain and erickkowalski big thanks no have the plugin working correctly. Eventually figured the motion and contacts were sitting at the top of the screen in HomeKit selected them created rooms ( I had created rooms in HomeBridge thought that woul create rooms in HomeKit) set up notifications and test walking past sensor and opening doors.
Now I just have to order up in wall modules for UK switches. Any recommendation greatly appreciated.

[5xPa]

I have connected the front door bell into Texecom Premier elite set as
Moment Key
Attributes set Monitor. Can be set to monitor only when armed.
If I am in the garden get and alert someone at door.

When door bell is pressed Texecom app produces and alert. Would be a nice piece of integration if this could be added to homebridge-texecom-connect.

[petersturrock]

I have set this up as per 5xPa's instruction on Wintex with Crestron set for the ComIP on ComPort2. It looks like the plugin is detecting changes as I move through the house but I don't see any notification on Homekit. Homebridge set on debug.

[2/28/2021, 8:36:42 PM] [TexecomConnect] Socket Data: ����x�x���x�x�x
[2/28/2021, 8:36:42 PM] [TexecomConnect] Reconnecting to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:36:42 PM] [TexecomConnect] Disconnected from SmartCom - 192.168.122.224:10001
[2/28/2021, 8:36:52 PM] [TexecomConnect] Connected to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:37:11 PM] [TexecomConnect] Socket Data: ����x�x��x�x�x
[2/28/2021, 8:37:11 PM] [TexecomConnect] Reconnecting to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:37:11 PM] [TexecomConnect] Disconnected from SmartCom - 192.168.122.224:10001
[2/28/2021, 8:37:21 PM] [TexecomConnect] Connected to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:37:23 PM] [TexecomConnect] Socket Data: ����x�x���x�x
[2/28/2021, 8:37:23 PM] [TexecomConnect] Reconnecting to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:37:23 PM] [TexecomConnect] Disconnected from SmartCom - 192.168.122.224:10001
[2/28/2021, 8:37:33 PM] [TexecomConnect] Connected to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:38:30 PM] [TexecomConnect] Socket Data: ����x�x�x��x�x�x
[2/28/2021, 8:38:30 PM] [TexecomConnect] Reconnecting to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:38:30 PM] [TexecomConnect] Disconnected from SmartCom - 192.168.122.224:10001
[2/28/2021, 8:38:40 PM] [TexecomConnect] Connected to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:39:04 PM] [TexecomConnect] Socket Data: ����x�x����x�x�x
[2/28/2021, 8:39:04 PM] [TexecomConnect] Reconnecting to SmartCom - 192.168.122.224:10001
[2/28/2021, 8:39:04 PM] [TexecomConnect] Disconnected from SmartCom - 192.168.122.224:10001
[2/28/2021, 8:39:14 PM] [TexecomConnect] Connected to SmartCom - 192.168.122.224:10001

I setup the zones on Homebridge UI as follows.

"zones": [
{
"accessory": "contact",
"name": "Front Door",
"number": 9
},
{
"accessory": "motion",
"name": "Lower Hall",
"number": 10
},
{
"accessory": "motion",
"name": "Office",
"number": 11
},
{
"accessory": "motion",
"name": "Upper Hall",
"number": 12
},
{
"accessory": "contact",
"name": "Back Door",
"number": 13
},
{
"accessory": "motion",
"name": "Kitchen",
"number": 14
},
{
"accessory": "motion",
"name": "Music Room",
"number": 15
},
{
"accessory": "motion",
"name": "Bedroom",
"number": 16
}

Any ideas ??

[5xPa]

Here is the Config I used. Also when I clicked on the config button after installing the plugin. The config as follows
{
"platform": "Texecom",
"ip_address": "192.168.0.7",
"ip_port": 10001,
"zones": [
{
"name": "Garage Pir",
"zone_number": "17",
"zone_type": "motion",
"dwell": 1000
},
{
"name": "Living Room Pir",
"zone_number": "18",
"zone_type": "motion",
"dwell": 1000
},
{
"name": "Dining Room Pir",
"zone_number": "19",
"zone_type": "motion",
"dwell": 1000
},
{
"name": "Kitchen Pir",
"zone_number": "20",
"zone_type": "motion",
"dwell": 1000
},
{
"name": "Upstairs Hall Pir",
"zone_number": "21",
"zone_type": "motion",
"dwell": 1000
},
{
"name": "Shed Pir",
"zone_number": "22",
"zone_type": "motion",
"dwell": 1000
},
{
"name": "Front Door",
"zone_number": "23",
"zone_type": "contact",
"dwell": 1000
},
{
"name": "Back Door",
"zone_number": "24",
"zone_type": "contact",
"dwell": 1000
},
{
"name": "Shed Window",
"zone_number": "25",
"zone_type": "contact",
"dwell": 1000
},
{
"name": "Garage Door",
"zone_number": "27",
"zone_type": "contact",
"dwell": 1000
},
{
"name": "Kitchen Window Left",
"zone_number": "28",
"zone_type": "contact",
"dwell": 1000
},
{
"name": "Kitchen Window Right",
"zone_number": "29",
"zone_type": "contact",
"dwell": 1000
},
{
"name": "Small Front Bedroom",
"zone_number": "31",
"zone_type": "motion",
"dwell": 1000
}
],
"areas": [
{
"name": "Downstairs",
"area_number": "2",
"area_type": "securitysystem",
"dwell": 1000
},
{
"name": "Shed",
"area_number": "4",
"area_type": "securitysystem",
"dwell": 1000
}
]
}

[petersturrock]

5xPa, is that the config for this texecom-connect plugin or the config for the other texecom plugin ? I created the config with the GUI and it looks very different.