Home Assistant OS 15.1

[sairon]

Home Assistant Operating System

• Update Docker to v28.0.4 (Update Docker to v28.0.4 #3974) @sairon
• Update generic_raw_uart and eq3_char_loop to latest versions (update generic_raw_uart and eq3_char_loop to latest versions #3964) @jens-maus

Raspberry Pi

ℹ️ There were several issues of intermittent upgrade problems on Raspberry Pi 5 (see #3943). Before you report an issue, try upgrading the EEPROM bootloader first, which resolved issues for majority of users. To do so, easiest way is to use a spare SD card with Raspberry Pi Imager and follow these instructions.

• Set initial_turbo=0 in config.txt on Raspberry Pi 3 (Set initial_turbo=0 in config.txt on Raspberry Pi 3 #3973) @sairon
• Backport RPi patches for PIO/RP1 firmware probing errors (Backport RPi patches for PIO/RP1 firmware probing errors #3972) @sairon

Home Assistant Yellow

• Backport RPi patches for PIO/RP1 firmware probing errors (Backport RPi patches for PIO/RP1 firmware probing errors #3972) @sairon

Home Assistant Green

• Linux: Update kernel to 6.12.20 (Linux: Update kernel to 6.12.20 #3971) @sairon

Open Virtual Appliance

• Linux: Update kernel to 6.12.20 (Linux: Update kernel to 6.12.20 #3971) @sairon
• Add Mellanox ConnectX-3 NIC support for kernel 6.12 (Add Mellanox ConnectX-3 NIC support for kernel 6.12 #3969) @greyltc
• Change i915 to module for proper initialization in VM passthrough (Change i915 to module for proper initialization in VM passthrough #3959) @sairon

Generic x86-64

• Linux: Update kernel to 6.12.20 (Linux: Update kernel to 6.12.20 #3971) @sairon
• Add Mellanox ConnectX-3 NIC support for kernel 6.12 (Add Mellanox ConnectX-3 NIC support for kernel 6.12 #3969) @greyltc
• Enable amdgpu SI and CIK support for x86 (Enable amdgpu SI and CIK support for x86 #3957) @sairon

Hardkernel ODROID

• Linux: Update kernel to 6.12.20 (Linux: Update kernel to 6.12.20 #3971) @sairon
• Add patches missing for ODROID-N2/C2/C4 to fix missing serial/I2C (Add patches missing for ODROID-N2/C2/C4 to fix missing serial/I2C #3947) @sairon
• Move ODROID-N2/C2/C4 U-Boot patch to correct folder to fix eMMC issues (Move ODROID-N2/C2/C4 U-Boot patch to correct folder to fix eMMC issues #3946) @sairon

ASUS Tinker

• Linux: Update kernel to 6.12.20 (Linux: Update kernel to 6.12.20 #3971) @sairon

Khadas VIM Series

• Linux: Update kernel to 6.12.20 (Linux: Update kernel to 6.12.20 #3971) @sairon

Generic aarch64

• Linux: Update kernel to 6.12.20 (Linux: Update kernel to 6.12.20 #3971) @sairon

Build System

• Add landing page test to the basic test set (Add landing page test to the basic test set #3928) @sairon

Dependencies

• Bump docker/login-action from 3.3.0 to 3.4.0 (Bump docker/login-action from 3.3.0 to 3.4.0 #3934) @dependabot[bot]

---

This discussion was created from the release Home Assistant OS 15.1.

[keithr59]

Home Assistant Green updated from 15.0 to 15.1. All OK.

[Anto79-ops]

There are no issues on installation and bootup on my NUC 12 (x86-64, bare-metal) with USB SkyConnect and USB Aeotec Z-Stick 7.

The system is running normally.

[m-rossi]

Someone with RaspberryPi 5 and ZHA already updated? I stayed on 12.2 because of #3352. May this EEP-ROM update may also solves this issue?

[jdeath]

15.1 no good on HP Intel(R) Core(TM) i5-8500 CPU @ 3.00GHz . Please fix

I could ssh in to 15.1 for a minute, then it froze, then came up again in a loop.

I did a ha os boot-slot other and 14.2 came right back.

Is their a way to clear the 15.1 boot slot so my 14.2 version stays intact?

edit: tried again today and installed correctly

[fonso2]

Were changes made on how HA detects Zigbee coordinators? I have an HA Green with both ZHA and Zigbee2MQTT (all devices here) configured. After the update, Zigbee2MQTT wouldn't run at all. ZHA was semi-populating itself and complaining that the configuration was changed (accept or restore previous config window). Had to manually pull out my ZHA Skyconnect dongle and delete the integration. Zigbee2MQTT seems to work again, for now at least...

[LanMart]

I had a similar issue.
The zigbee coordinator I use for ZHA works fine. My (USB) connection to the DSMR smart meter seems to work as well. However, for zigbee2mqtt, on the config-tab of the add-on, under serial, i had to change to port: /dev/ttyUSB0 (was USB1).

Is the USB port mapping different? Automatically corrected/detected by ZHA and DSMR, but not by Zigbee2MQTT?

[r0l01]

HA Blue with stock eMMC upgraded fine to 15.1. Had huge issues with 15.0.

[NickdeK]

HP T620 that failed with 15.0 works now with 15.1.

[hvandonge]

Thanks, I was looking for this. Anybody tested 15.1 with T520 already?
Edit: I just updated, it is working on T520 as well

[Picard16]

No problems with RasPi5 from 15.0 to 15.1.
SD card, zigbee2mqtt, 8GB

[Raziel79x]

I see that both the Pi 5 has issues with the update and 3 needs a line added to the configuration file. Anyone update a Pi 4? Any issues? I'm not home right now and I don't want calls from the wife about things not working. 😄

[chrsfrwll]

HA Green updated to 15.1 with no errors or problems

[EinfachHans]

No problems updating Pi5 from 15.0 to 15.1

[Yabi23]

HP T620 which did not work with version 15.0 still does not work with version 15.1.

[JeyP91]

I think I have the same issue. Removing the iGPU passthrough fixed it for me. I think it has to do with the changed i915 module.

[back-2-95]

Started the update from UI (mac mini 2012) and now I just got onboarding window. Also SSH does not let me in.

[jurijzahn8019]

Works on Fujitsu futro s920 gx 415ga
15.0 didn't. But 15.1 works just fine.

[gorecrob]

Not working with DELL OptiPlex 7050