2.3.0 Release Notes
Hello and welcome to INAV 2.3.0 Release!
Please carefully read all of this document for the best possible experience and safety.
Get in touch with other pilots, share experiences, suggestions and ask for help on:
 |
INAV Official on Telegram |
 |
INAV Official on Facebook |
Please continue to support developers, for free, by checking out from the following stores after having clicked on the following links:
 |
Support us on Banggood |
Your contribution from the past month has been very welcome! Thanks!
Tested and suggested hardware can be found here
- Download and install the new configurator
- Save to a file the current diff all from the CLI.
- Upgrade to INAV 2.3 using the Full Erase option in the configurator.
- Upload your OSD font of choice from the OSD tab.
- Go the CLI again and paste the contents on the file you previously create and write save , press ENTER and done!
- You should be ready, explore new 2.3 features and enjoy!
- Please follow the upgrade guide to 2.2.0 and then step to the previous section.
| Setting | Description |
|---|---|
| dyn_notch_width_percent | Distance in % of the attenuated frequency for double dynamic filter notched. When set to 0 single dynamic notch filter is used |
| dyn_notch_range | Dynamic gyro filter range. Possible values LOW MEDIUM HIGH. MEDIUM should work best for 5-6" multirotors. LOW should work best with 7" and bigger. HIGH should work with everything below 4" |
| dyn_notch_q | Q factor for dynamic notches |
| dyn_notch_min_hz | Minimum frequency for dynamic notches. Default value of 150 works best with 5" multirors. Should be lowered with increased size of propellers. Values around 100 work fine on 7" drones. 10" can go down to 60 - 70
|
| throttle_scale | Throttle scaling factor. 1 means no throttle scaling. 0.5 means throttle scaled down by 50% |
| vbat_meter_type | Vbat voltage source. Possible values: NONE, ADC, ESC. ESC required ESC telemetry enabled and running |
| antigravity_gain | Max Antigravity gain. 1 means Antigravity is disabled, 2 means Iterm is allowed to double during rapid throttle movements |
| antigravity_accelerator | |
| antigravity_cutoff_lpf_hz | Antigravity cutoff frequenct for Throtte filter. Antigravity is based on the difference between actual and filtered throttle input. The bigger is the difference, the bigger Antigravity gain |
| sim_pin | PIN for GSM card module |
ESC Telemetry is a feature of DSHOT ESCs to send some data back to the flight controller - voltage, current, temperature, motor RPM. It required additional wire from an ESC to the flight controller. To configure you need DSHOT as a motor protocol and "ESC output/telemetry" function enabled for the serial port where ESC telemetry wires are connected.
INAV ESC Telemetry with BlHeli_32 - The Complete Guide
Dynamic Filters is a port of Betaflight dynamic filtering. It uses FFT analysis of gyro traces to locate noise peaks and double notch filters to attenuate them. By default, there are 6 notches, 2 per each axis: roll, pitch and yaw.
To enable Dynamic Filters, go to CLI and type
feature DYNAMIC_FILTERS
The default values are suited for 5" mini quads. Depending on the size of multirotor propellers, some adjustments might be required.
| Propeller size | dyn_notch_range |
dyn_notch_min_hz |
|---|---|---|
| Below 5" | HIGH |
200 or more |
| 5" |
HIGH or MEDIUM
|
150 or more |
| 7" | LOW |
100 or less |
INAV Dynamic Filters, one of INAV 2.3 goodies - how-to guide
Global Functions (abbr. GF) are a mechanism allowing to override certain flight parameters (during flight). Global Functions are activated by Logic Conditions.
Currently implemented Global Functions
| Name | Notes |
|---|---|
| OVERRIDE_ARMING_SAFETY | Allows to arm on any angle even without GPS fix |
| OVERRIDE_THROTTLE_SCALE | Override throttle scale to the defined value |
| SWAP_ROLL_YAW | basically, when activated, yaw stick will control roll and roll stick will control yaw. Required for tail-sitters VTOL during vertical-horizonral transition when body frame changes |
| SET_VTX_POWER_LEVEL | Sets VTX power level. Allows to change VTX power level based on distance, switch or other values present in Logic Conditions |
| INVERT_ROLL | Inverts ROLL axis input for PID/PIFF controller |
| INVERT_PITCH | Inverts PITCH axis input for PID/PIFF controller |
| INVERT_YAW | Inverts YAW axis input for PID/PIFF controller |
| OVERRIDE_THROTTLE | Override throttle value that is fed to the motors by mixer. Allows for throttle hold |
For details refer to Global Functions.md in docs folder.
INAV now supports pixel based OSDs and includes a driver for FrSky's OSD. Some elements, like the artificial horizon, the home arrow or the heading graph include pixel based implementations.
To enable it go to the Ports tab in the configurator and select "FrSky OSD" from the peripherals column of the port that the OSD is connected to. Font uploading and OSD element configuration works in the same way, regardless of the OSD type.
The iNav Makefile will attempt to install a recommended compiler for your platform. Should you wish to override this, or your platform is not supported, please refer to the document docs/development/Generic_Linux_development.md which describes how to use an alternative compiler.