Unable to find an inverter

[miralemR]

Hello.
When I want to add a card on dashboard I get this message

Unable to find an inverter with the device ID or friendly name ''. Valid friendly names: 'Ngen H3'

Should I reinstall Foxess modbus integration an leave name window empty?

[canton7]

Are you referring to the charge period card? https://github.com/nathanmarlor/foxess_modbus_charge_period_card

[miralemR]

Yes. V sre., 17. jan. 2024, 17:17 je oseba Antony Male ***@***.***> napisala:

…

Are you referring to the charge period card? https://github.com/nathanmarlor/foxess_modbus_charge_period_card — Reply to this email directly, view it on GitHub <#517 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AV6JHHSIHJIPIUURCWV4YTTYO72RXAVCNFSM6AAAAABB6T2XZSVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DCNJYHE2TC> . You are receiving this because you authored the thread.Message ID: ***@***.*** com>

[canton7]

So, use 'Ngen H3' as the friendly name of the inverter to use when you configure the card, or select your inverter from the drop-down.

[miralemR]

Hello again. I am still having problems with the charge periods card. I have been searching for problems that might be on my configuration specifically but can't seem to find them. I have tried to select the inverter from the drop-down but it doesn't show up. I also tried to insert it in the code editor but the card just says loading and never loads (I have waited a few days to be sure). I have added screenshots of my charge periods card configuration if it is of any help. "Ni ustreznih naprav" means "no suitable devices". Thank you for your help. V V sre., 17. jan. 2024 ob 18:27 je oseba Antony Male < ***@***.***> napisala:

…

So, use 'Ngen H3' as the friendly name of the inverter to use when you configure the card, or select your inverter from the drop-down. — Reply to this email directly, view it on GitHub <#517 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AV6JHHSF56MURSEWCLH5O7DYPACW5AVCNFSM6AAAAABB6T2XZSVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DCNJZG44DI> . You are receiving this because you authored the thread.Message ID: ***@***.*** com>

[canton7]

The H3 does not support setting charge periods over modbus I'm afraid

[miralemR]

What about the Foxess- energy management integration? I have an ethernet adapter as a modbus host and I connect to it with rs485. Foxess energy management says that it needs to be RTU -> TCP, not direct LAN. When I insert the IP address it gives an error. What am I doing wrong / is there any workaround or...? V V ned., 10. mar. 2024 ob 18:23 je oseba Antony Male < ***@***.***> napisala:

…

The H3 does not support setting charge periods over modbus I'm afraid — Reply to this email directly, view it on GitHub <#517 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AV6JHHWAEIY6KOPC4JKDLDTYXSJIRAVCNFSM6AAAAABB6T2XZSVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DOMZWHE3DS> . You are receiving this because you authored the thread.Message ID: ***@***.*** com>

[canton7]

For foxess_em questions, please raise a discussion on the foxess_em repo.