Skip to content
This repository has been archived by the owner on Sep 30, 2024. It is now read-only.

Home

Jump to bottom
notro edited this page Nov 2, 2015 · 159 revisions

Linux Framebuffer drivers for small TFT LCD display modules.

<img src="http://www.adafruit.com/images/ID797.jpg" title="Video: Raspberry Pi boots with Adafruit 2.2" LCD display" border="10" />

For a list of all wikipages see Pages

Install

The FBTFT drivers are now included in the Raspberry Pi Foundation kernel and can be installed with plain rpi-update.

SPI controller driver with DMA support
The spi-bcm2835 driver has now gotten DMA support, so we don't need the out-of-tree spi-bcm2708 anymore. This means that I will stop making updates to the custom FBTFT kernel. To maximize throughput, make sure txbuflen is 16k or 32k (default is usually 4k). This is needed because of the dma mapping/engine overhead per transfer that spi-bcm2835 has.

Device Tree: txbuflen = <32768>;
fbtft_device txbuflen=32768

# Here it is 16k
$ dmesg | grep graphics
[    8.547173] graphics fb1: fb_ili9341 frame buffer, 320x240, 150 KiB video memory, 16 KiB DMA buffer memory, fps=50, spi0.0 at 48 MHz

See /boot/overlays/README and FBTFT RPI overlays for information about Device Tree overlays.

To use fbtft_device instead of a DT overlay, add to /boot/config.txt:

dtparam=spi=on

Step-by-step using FBTFT (without Device Tree)

Using the Adafruit 2.2" display as an example

Enable driver

Register device (the driver will load automatically)
sudo modprobe fbtft_device name=adafruit22

dmesg will show the default pin assignements, and that the driver is loaded.

   fbtft_device:  SPI devices registered:
   fbtft_device:      spidev spi0.0 500kHz 8 bits mode=0x00
   fbtft_device:      spidev spi0.1 500kHz 8 bits mode=0x00
   fbtft_device:  'fb' Platform devices registered:
   fbtft_device:      bcm2708_fb id=-1 pdata? no
   fbtft_device: Deleting spi0.0
   fbtft_device:  GPIOS used by 'adafruit22':
   fbtft_device:    'reset' = GPIO25
   fbtft_device:    'led' = GPIO23
   fbtft_device:  SPI devices registered:
   fbtft_device:      spidev spi0.1 500kHz 8 bits mode=0x00
   fbtft_device:      fb_hx8340bn spi0.0 32000kHz 8 bits mode=0x00
   graphics fb1: fb_hx8340bn frame buffer, 176x220, 75 KiB video memory, 16 KiB buffer memory, fps=20, spi0.0 at 32 MHz

Test

X Windows
FRAMEBUFFER=/dev/fb1 startx

Note: You might need to move an xorg config out of the way if X doesn't start:

sudo mv /usr/share/X11/xorg.conf.d/99-fbturbo.conf ~
Console
con2fbmap 1 1

Make it permanent (Debian Jessie, Arch Linux, systemd)

Add to file /etc/modules-load.d/raspberrypi.conf

fbtft_device

Add to file /etc/modprobe.d/fbtft.conf

options fbtft_device name=adafruit22

Thanks

Without the help from other people, this project would not exist

  • Matt Porter wrote st7735fb which FBTFT grew from
  • Texy has provided much input and testing that have helped move this project forward
  • Derek Campbell did the work to implement DMA
  • Several people have provided drivers and improvements
  • Donations have helped me buy displays and accessories

Also thanks to people that help answering questions about FBTFT.

piwik

Clone this wiki locally