CISCO-LWAPP-QOS-MIB.mib

-- *******************************************************************
-- CISCO-LWAPP-QOS-MIB.my
-- November 2005, Devesh Pujari, Bharat Biswal,
-- Prasanna Viswakumar, Srinath Candadai
--   
-- Copyright (c) 2005-2007 by Cisco Systems Inc.
-- All rights reserved.
-- ******************************************************************

CISCO-LWAPP-QOS-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    Unsigned32,
    Counter32,
    Gauge32
        FROM SNMPv2-SMI
    MODULE-COMPLIANCE,
    OBJECT-GROUP
        FROM SNMPv2-CONF
    TruthValue
        FROM SNMPv2-TC
    cLApDot11IfEntry
        FROM CISCO-LWAPP-AP-MIB
    cLWlanConfigEntry
        FROM CISCO-LWAPP-WLAN-MIB
    ciscoMgmt
        FROM CISCO-SMI;

-- ********************************************************************
-- *  MODULE IDENTITY
-- ********************************************************************

ciscoLwappQosMIB MODULE-IDENTITY
    LAST-UPDATED    "200701070000Z"
    ORGANIZATION    "Cisco Systems Inc."
    CONTACT-INFO
            "Cisco Systems,
            Customer Service
            Postal: 170 West Tasman Drive
            San Jose, CA  95134
            USA
            Tel: +1 800 553-NETS

            Email: cs-wnbu-snmp@cisco.com"
    DESCRIPTION
        "This MIB is intended to be implemented on all those
        devices operating as Central controllers, that
        terminate the Light Weight Access Point Protocol
        tunnel from Cisco Light-weight LWAPP Access Points.

        Information provided by this MIB is used to study
        the quality of service in the voice and video traffic
        on the WLAN.

        The relationship between CC and the LWAPP APs
        can be depicted as follows:

              +......+     +......+     +......+
              +      +     +      +     +      +
              +  CC  +     +  CC  +     +  CC  +
              +      +     +      +     +      +
              +......+     +......+     +......+
                ..            .             .
                ..            .             .
               .  .            .             .
              .    .            .             .
             .      .            .             .
            .        .            .             .
        +......+ +......+     +......+      +......+
        +      + +      +     +      +      +      +
        +  AP  + +  AP  +     +  AP  +      +  AP  +
        +      + +      +     +      +      +      +
        +......+ +......+     +......+      +......+
                   .              .             .
                 .  .              .             .
                .    .              .             .
               .      .              .             .
              .        .              .             .
           +......+ +......+     +......+      +......+
           +      + +      +     +      +      +      +
           +  MN  + +  MN  +     +  MN  +      +  MN  +
           +      + +      +     +      +      +      +
           +......+ +......+     +......+      +......+


        The LWAPP tunnel exists between the controller and
        the APs.  The MNs communicate with the APs through
        the protocol defined by the 802.11 standard.

        LWAPP APs, upon bootup, discover and join one of the
        controllers and the controller pushes the configuration,
        that includes the WLAN parameters, to the LWAPP APs.
        The APs then encapsulate all the 802.11 frames from
        wireless clients inside LWAPP frames and forward
        the LWAPP frames to the controller.

                           GLOSSARY

        Access Point ( AP )

        An entity that contains an 802.11 medium access
        control ( MAC ) and physical layer ( PHY ) interface
        and provides access to the distribution services via
        the wireless medium for associated clients.  

        LWAPP APs encapsulate all the 802.11 frames in
        LWAPP frames and sends them to the controller to which
        it is logically connected.

        Gratuitous Probe Response (GPR)

        The Gratuitous Probe Response feature aids in conserving
        battery power of WLAN-enabled cell phones by providing
        a high rate packet on the order of tens of milliseconds
        such that these kind of phones can wake up and wait at
        predefined intervals, to reduce battery power.  The 
        GPR packet is transmitted from the AP at a predefined
        time interval.


        Light Weight Access Point Protocol ( LWAPP )

        This is a generic protocol that defines the 
        communication between the Access Points and the
        Central Controller. 

        Mobile Node ( MN )

        A roaming 802.11 wireless device in a wireless
        network associated with an access point. Mobile Node 
        and client are used interchangeably. 

        TU

        A measurement of time in units of 1024 microseconds.

        User Priority ( UP )

        Specifies a the priority rules in QOS for handling user 
        priority.

        REFERENCE

        [1] Wireless LAN Medium Access Control ( MAC ) and
        Physical Layer ( PHY ) Specifications

        [2] Draft-obara-capwap-lwapp-00.txt, IETF Light 
        Weight Access Point Protocol"
    REVISION        "200701070000Z"
    DESCRIPTION
        "Added ciscoLwappQosDot11aConfigGroupSup1 and
        ciscoLwappQosDot11bConfigGroupSup1 objects."
    REVISION        "200604130000Z"
    DESCRIPTION
        "Initial version of this MIB module."
    ::= { ciscoMgmt 524 }


ciscoLwappQosMIBNotifs  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIB 0 }

ciscoLwappQosMIBObjects  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIB 1 }

ciscoLwappQosMIBConform  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIB 2 }

cLQd11aCACConfig  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIBObjects 1 }

cLQd11bCACConfig  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIBObjects 2 }

cLQd11GprConfig  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIBObjects 3 }

cLQd11CACStats  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIBObjects 4 }

cLQEntConfConfig  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIBObjects 5 }


-- ********************************************************************
-- *    Configuration for Call Admission Control parameters
-- *    for VOICE traffic in 802.11a interfaces in the controller
-- ********************************************************************
cLQd11aVoiceAdmCtrlSupport OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object is used to enable or disable admission
        control for voice traffic flowing through the 802.11a 
        interfaces in the controller.

        When set to 'true', controller will reserve and manage 
        max-bandwidth (cLQd11aVoiceMaxAdmBandwidth) 
        and roaming-bandwidth
        (cLQd11aVoiceMaxRoamBandwidth) as per user 
        configured values.

        When disabled, admission control will not be enforced. 
        This may delay voice traffic depending on load on
        the WLAN."
    DEFVAL          { true } 
    ::= { cLQd11aCACConfig 1 }

cLQd11aVoiceMaxAdmBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object denotes the maximum bandwidth
        that can be allocated by controller for voice
        traffic when admission control is enabled for
        for 802.11a interfaces in the controller.

        Please note that the write operation on this
        object will be successful only if the 802.11a
        network is not operational and the total
        value populated for this object for all the
        admission control attributes (voice, video)
        together does not exceed 100%." 
    ::= { cLQd11aCACConfig 2 }

cLQd11aVoiceMaxRoamBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object represents the bandwidth relative
        to the maximum allocated bandwidth indicated by
        cLQd11aVoiceMaxAdmBandwidth, that can be 
        allocated to roaming clients for voice traffic,
        when admission control is enabled for 802.11a
        interfaces in the controller.

        Please note that the write operation on this
        object will be successful only if the 802.11a
        network is disabled and not operational.  The
        value configured through this object takes
        effect when the 802.11a network is enabled."
    DEFVAL          { 0 } 
    ::= { cLQd11aCACConfig 3 }

-- ********************************************************************
-- *    Configuration for Call Admission Control parameters
-- *    for VIDEO traffic in 802.11a interfaces in the controller
-- ********************************************************************
cLQd11aVideoAdmCtrlSupport OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object is used to enable or disable admission
        control for video traffic flowing through the 802.11a 
        interfaces in the controller.

        When set to 'true', controller will reserve and manage 
        max-bandwidth (cLQd11aVideoMaxAdmBandwidth) 
        and roaming-bandwidth
        (cLQd11aVideoMaxRoamBandwidth) as per user  
        configured values.

        When disabled, admission control will not be enforced. 
        This may delay video traffic depending on load on
        the WLAN."
    DEFVAL          { true } 
    ::= { cLQd11aCACConfig 4 }

cLQd11aVideoMaxAdmBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object denotes the maximum bandwidth
        that can be allocated by controller for video traffic
        when admission control is enabled for 802.11a 
        interfaces in the controller.  When set to 0, all
        available bandwidth in 802.11a interfaces can be
        allocated to video traffic.

        Please note that the write operation on this
        object will be successful only if the 802.11a
        network is not operational and the total
        value populated for this object for all the
        admission control attributes (voice, video)
        together does not exceed 100%."
    DEFVAL          { 0 } 
    ::= { cLQd11aCACConfig 5 }

cLQd11aVideoMaxRoamBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object represents the bandwidth relative
        to the maximum allocated bandwidth indicated by
        cLQd11aVideoMaxAdmBandwidth, that can be 
        allocated to roaming clients for video traffic,
        when admission control is enabled for 802.11a
        interfaces in the controller.

        Please note that the write operation on this
        object will be successful only if the 802.11a
        network is disabled and not operational.  The
        value configured through this object takes effect 
        when the 802.11a network is enabled and 
        operational."
    DEFVAL          { 0 } 
    ::= { cLQd11aCACConfig 6 }

-- ********************************************************************
-- *    Configuration for  Call Admission Control parameters
-- *    for VOICE traffic in 802.11b/g interfaces in the controller
-- ********************************************************************
cLQd11bVoiceAdmCtrlSupport OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object is used to enable or disable admission
        control for voice traffic flowing through the 
        802.11b/g interfaces in the controller.

        When set to 'true', controller will reserve and manage
        max-bandwidth (cLQd11bVoiceMaxAdmBandwidth)
        and roaming-bandwidth
        (cLQd11bVoiceMaxRoamingBandwidth) as per user
        configured values.

        When disabled, admission control will not be enforced. 
        This may delay voice traffic depending on load on the 
        WLAN."
    DEFVAL          { true } 
    ::= { cLQd11bCACConfig 1 }

cLQd11bVoiceMaxAdmBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object denotes the maximum bandwidth that
        can be allocated by controller for voice traffic 
        when admission control is enabled for 802.11b/g
        interfaces in the controller.

        Please note that the write operation on this
        object will be successful only if the 802.11b/g
        network is not operational and the total
        value populated for this object for all the
        admission control attributes (voice, video)
        together does not exceed 100%." 
    ::= { cLQd11bCACConfig 2 }

cLQd11bVoiceMaxRoamBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object represents the bandwidth relative
        to the maximum allocated bandwidth indicated by
        cLQd11bVoiceMaxAdmBandwidth, that can be 
        allocated to roaming clients for voice traffic,
        when admission control is enabled for 802.11b
        interfaces in the controller.

        Please note that the write operation on this
        object will be successful only if the 802.11b/g
        network is not operational.  The value configured
        through this object takes effect when the 802.11b/g
        network is enabled and operational."
    DEFVAL          { 0 } 
    ::= { cLQd11bCACConfig 3 }

-- ********************************************************************
-- *    Configuration for Call Admission Control parameters
-- *    for VIDEO traffic in 802.11b/g interfaces in the controller
-- ********************************************************************
cLQd11bVideoAdmCtrlSupport OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object is used to enable or disable admission
        control for video traffic flowing through the 
        802.11b/g interfaces in the controller.

        When set to 'true', controller will reserve and manage
        max-bandwidth (cLQd11bVideoMaxAdmBandwidth) 
        and roaming-bandwidth
        (cLQd11bVideoMaxRoamBandwidth) as per user 
        configured values.

        When disabled, admission control will not be enforced. 
        This may delay video traffic depending on load on the 
        WLAN."
    DEFVAL          { true } 
    ::= { cLQd11bCACConfig 4 }

cLQd11bVideoMaxAdmBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object denotes the maximum bandwidth that
        can be allocated by controller for video traffic when
        admission control is enabled for 802.11b/g interfaces 
        in the controller.  When set to 0, all available
        bandwidth in 802.11b/g interfaces can be allocated
        to video traffic.

        Please note that the write operation on this
        object will be successful only if the 802.11b/g
        network is not operational and the total
        value populated for this object for all the
        admission control attributes (voice, video)
        together does not exceed 100%."
    DEFVAL          { 0 } 
    ::= { cLQd11bCACConfig 5 }

cLQd11bVideoMaxRoamBandwidth OBJECT-TYPE
    SYNTAX          Unsigned32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This objects represents the bandwidth relative
        to the maximum allocated bandwidth indicated by
        cLQd11bVideoMaxAdmBandwidth, that can be 
        allocated to roaming clients for video traffic,
        when admission control is enabled for 802.11b
        interfaces in the controller.

        Please note that the write operation on this
        object will be successful only if the 802.11b/g
        network is not operational.  The value configured
        through this object takes effect when the 802.11b/g
        network is enabled and operational."
    DEFVAL          { 0 } 
    ::= { cLQd11bCACConfig 6 }

-- ********************************************************************
-- *    Configuration of GPR (Gratuitous Probe Response) probe interval
-- *    for all 802.11a interfaces in the controller
-- ********************************************************************
cLQd11aGprProbeInterval OBJECT-TYPE
    SYNTAX          Unsigned32 (10..100 )
    UNITS           "TU"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object is used to set GPR probe interval
        period to be used by all 802.11a interfaces in the 
        controller, when the radios are advertising any 
        WLAN with GPR support enabled.

        Please note that the write operation on this
        object will be successful only if the 802.11a
        network is not operational.  The value configured
        through this object takes effect when the 802.11a
        network is enabled and operational."
    DEFVAL          { 10 } 
    ::= { cLQd11aCACConfig 7 }

cLQd11aVoiceCtrl OBJECT-TYPE
    SYNTAX          INTEGER  {
                        loadBased(1),
                        static(2)
                    }
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "When admission control is enabled these parameters
        can be modified.
            loadBased - controller will reserve and manage
                        max-bandwidth and roaming-bandwidth
                        based on the load on the WLAN. 
            static    - controller will reserve and
                        manage max-bandwidth 
                        (cLQd11aVoiceMaxAdmBandwidth)
                        and roaming-bandwidth
                        (cLQd11aVoiceMaxRoamBandwidth) 
                        as per user configured values.
         When ACM is disabled, admission control will not 
         be enforced. This may delay voice traffic depending 
         on the traffic on the WLAN."
    DEFVAL          { loadBased } 
    ::= { cLQd11aCACConfig 8 }

cLQd11aExpeditedBw OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies if expedited BW feature is
        enabled or not.
        A value of 'true' will ensure that the APs advertise
        the expedited BW support in their beacons and 
        association responses.
        A value of 'false' will ensure that the APs do not
        advertise the expedited BW support in their beacons 
        and association responses." 
    ::= { cLQd11aCACConfig 9 }

-- ********************************************************************
-- *    Configuration of GPR (Gratuitous Probe Response) probe interval
-- *    for all 802.11b/g interfaces in the controller
-- ********************************************************************
cLQd11bGprProbeInterval OBJECT-TYPE
    SYNTAX          Unsigned32 (10..100 )
    UNITS           "TU"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object is used to set GPR probe interval
        period to be used by all 802.11b/g interfaces in the 
        controller, when the radios are advertising any 
        WLAN with GPR support enabled.

        Please note that the write operation on this
        object will be successful only if the 802.11b/g
        network is not operational.  The value configured
        through this object takes effect when the 802.11b/g
        network is enabled."
    DEFVAL          { 10 } 
    ::= { cLQd11bCACConfig 7 }

cLQd11bVoiceCtrl OBJECT-TYPE
    SYNTAX          INTEGER  {
                        loadBased(1),
                        static(2)
                    }
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "When admission control is enabled these parameters
        can be modified.
            loadBased - controller will reserve and manage
                        max-bandwidth and roaming-bandwidth
                        based on the load on the WLAN. 
            static    - controller will reserve and
                        manage max-bandwidth 
                        (cLQd11bVoiceMaxAdmBandwidth)
                        and roaming-bandwidth
                        (cLQd11bVoiceMaxRoamBandwidth) 
                        as per user configured values.
         When ACM is disabled, admission control will not 
         be enforced. This may delay voice traffic depending 
         on the traffic on the WLAN."
    DEFVAL          { loadBased } 
    ::= { cLQd11bCACConfig 8 }

cLQd11bExpeditedBw OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies if expedited BW feature is
        enabled or not.
        A value of 'true' will ensure that the APs advertise
        the expedited BW support in their beacons and 
        association responses.
        A value of 'false' will ensure that the APs do not
        advertise the expedited BW support in their beacons 
        and association responses." 
    ::= { cLQd11bCACConfig 9 }
-- ********************************************************************
-- Table to represent (Gratuitous Probe Response) GPR
-- parameters per each WLAN.
-- ********************************************************************

cLQd11GprTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CLQd11GprEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table populates the GPR configuration on the
        WLANs configured on this controller.  

        There exists a row in this table for each WLAN
        configured through cLWlanConfigTable.  A row is added
        is to this table by the agent when a WLAN is created
        by the user through an explicit management action
        initiated from a network management station.
        Similarly a row gets deleted automatically when the
        user deletes the particular WLAN."
    ::= { cLQd11GprConfig 1 }

cLQd11GprEntry OBJECT-TYPE
    SYNTAX          CLQd11GprEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Each entry represents a conceptual row in
        cLQd11GprTable and corresponds to the
        GPR configuration on a WLAN."
    AUGMENTS           { cLWlanConfigEntry  } 
 
    ::= { cLQd11GprTable 1 }

CLQd11GprEntry ::= SEQUENCE {
        cLQd11GprSupport TruthValue
}

cLQd11GprSupport OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "If 'true', then the corresponding radios that
        advertise this WLAN, will send Gratuitous Probe 
        Response.  If 'false', then the corresponding radios 
        that advertise this WLAN, will not send Gratuitous 
        Probe Response."
    DEFVAL          { false } 
    ::= { cLQd11GprEntry 1 }
 

-- ********************************************************************
-- *  CALL admission control statistics
-- ********************************************************************

cLQd11CACStatsTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CLQd11CACStatsEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table populates the call admission control
        metrics collected by observing the voice or video
        traffic on the dot11 interface of a particular
        AP. 

        There exists a row in this table for each row
        corresponding to a dot11 interface found in
        cLApDot11IfTable.  A row corresponding to a
        dot11 interface is added when an AP joins the
        controller.  The row gets deleted when the AP
        dissociates from the controller."
    ::= { cLQd11CACStats 1 }

cLQd11CACStatsEntry OBJECT-TYPE
    SYNTAX          CLQd11CACStatsEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Each entry represents a conceptual row in
        CLQd11CACStatsTable and corresponds to the 
        admission control statistics for a particular
        dot11 interface."
    AUGMENTS           { cLApDot11IfEntry  } 
 
    ::= { cLQd11CACStatsTable 1 }

CLQd11CACStatsEntry ::= SEQUENCE {
        cLQd11CacVoiceBwInUse         Gauge32,
        cLQd11CacVideoBwInUse         Gauge32,
        cLQd11CacVoiceCallsInProgress Gauge32,
        cLQd11CacRoamVoiceCallsInProg Gauge32,
        cLQd11CacTotalVoiceCallsAP    Counter32,
        cLQd11CacTotalRoamCallsAP     Counter32,
        cLQd11CacVoiceCallsRejectedAP Counter32,
        cLQd11CacRoamCallsRejectedAP  Counter32,
        cLQd11CacRejCallsInsufBw      Counter32,
        cLQd11CacRejCallsBadParams    Counter32,
        cLQd11CacRejCallsPhyRate      Counter32,
        cLQd11CacRejCallsQosPolicy    Counter32
}

cLQd11CacVoiceBwInUse OBJECT-TYPE
    SYNTAX          Gauge32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the voice bandwidth in use
        as a percentage of the bandwidth configured through
        cLQd11aVoiceMaxAdmBandwidth or
        cLQd11bVoiceMaxAdmBandwidth, depending on the type
        of this dot11 interface." 
    ::= { cLQd11CACStatsEntry 1 }

cLQd11CacVideoBwInUse OBJECT-TYPE
    SYNTAX          Gauge32 (0..100 )
    UNITS           "Percent"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the video bandwidth in use
        as a percentage of the bandwidth configured through
        cLQd11aVideoMaxAdmBandwidth or
        cLQd11bVideoMaxAdmBandwidth, depending on the type
        of this dot11 interface." 
    ::= { cLQd11CACStatsEntry 2 }

cLQd11CacVoiceCallsInProgress OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        voice calls currently in progress on this dot11
        interface." 
    ::= { cLQd11CACStatsEntry 3 }

cLQd11CacRoamVoiceCallsInProg OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        voice calls initiated from roaming clients
        currently in progress on this dot11 interface." 
    ::= { cLQd11CACStatsEntry 4 }

cLQd11CacTotalVoiceCallsAP OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        voice calls observed on this dot11 interface
        ever since this AP has joined the controller." 
    ::= { cLQd11CACStatsEntry 5 }

cLQd11CacTotalRoamCallsAP OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        voice and video calls initiated from roaming clients
        observed on this dot11 interface ever since
        this AP has joined the controller." 
    ::= { cLQd11CACStatsEntry 6 }

cLQd11CacVoiceCallsRejectedAP OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        voice calls observed as rejected on this dot11
        interface, ever since this AP has joined the
        controller." 
    ::= { cLQd11CACStatsEntry 7 }

cLQd11CacRoamCallsRejectedAP OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        voice and video calls initiated from roaming
        clients observed as rejected on this dot11
        interface, ever since this AP has joined the
        controller." 
    ::= { cLQd11CACStatsEntry 8 }

cLQd11CacRejCallsInsufBw OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        calls observed as rejected on this dot11
        interface due to insufficient bandwidth, ever
        since this AP has joined the controller." 
    ::= { cLQd11CACStatsEntry 9 }

cLQd11CacRejCallsBadParams OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        calls observed as rejected on this dot11
        interface due to mismatch in call parameters, ever
        since this AP has joined the controller." 
    ::= { cLQd11CACStatsEntry 10 }

cLQd11CacRejCallsPhyRate OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        calls observed as rejected on this dot11
        interface due to mismatch in 802.11 data rates,
        ever since this AP has joined the controller." 
    ::= { cLQd11CACStatsEntry 11 }

cLQd11CacRejCallsQosPolicy OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the count of the number of
        calls observed as rejected on this dot11
        interface due to restrictions imposed by QOS
        policies, ever since this AP has joined the
        controller." 
    ::= { cLQd11CACStatsEntry 12 }
 

-- ********************************************************************
-- *    Compliance statements
-- ********************************************************************
ciscoLwappQosMIBCompliances  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIBConform 1 }

ciscoLwappQosMIBGroups  OBJECT IDENTIFIER
    ::= { ciscoLwappQosMIBConform 2 }


ciscoLwappQosMIBCompliance MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
        "The compliance statement for the SNMP entities that
        implement the ciscoLwappQosMIB module."
    MODULE          -- this module
    MANDATORY-GROUPS {
                        ciscoLwappQosDot11aConfigGroup,
                        ciscoLwappQosDot11bConfigGroup,
                        ciscoLwappQosDot11WlanConfigGroup,
                        ciscoLwappQosDot11CacStatsGroup
                    }
    ::= { ciscoLwappQosMIBCompliances 1 }

ciscoLwappQosMIBComplianceRev1 MODULE-COMPLIANCE
    STATUS          current
    DESCRIPTION
        "The compliance statement for the SNMP entities that
        implement the ciscoLwappQosMIB module."
    MODULE          -- this module
    MANDATORY-GROUPS {
                        ciscoLwappQosDot11aConfigGroup,
                        ciscoLwappQosDot11bConfigGroup,
                        ciscoLwappQosDot11WlanConfigGroup,
                        ciscoLwappQosDot11CacStatsGroup,
                        ciscoLwappQosDot11aConfigGroupSup1,
                        ciscoLwappQosDot11bConfigGroupSup1
                    }
    ::= { ciscoLwappQosMIBCompliances 2 }

-- ********************************************************************
-- *    Units of conformance
-- ********************************************************************
ciscoLwappQosDot11aConfigGroup OBJECT-GROUP
    OBJECTS         {
                        cLQd11aVoiceAdmCtrlSupport,
                        cLQd11aVoiceMaxAdmBandwidth,
                        cLQd11aVoiceMaxRoamBandwidth,
                        cLQd11aVideoAdmCtrlSupport,
                        cLQd11aVideoMaxAdmBandwidth,
                        cLQd11aVideoMaxRoamBandwidth,
                        cLQd11aGprProbeInterval
                    }
    STATUS          current
    DESCRIPTION
        "This collection of objects represents the
        quality-of-service parameters 802.11a networks."
    ::= { ciscoLwappQosMIBGroups 1 }

ciscoLwappQosDot11bConfigGroup OBJECT-GROUP
    OBJECTS         {
                        cLQd11bVoiceAdmCtrlSupport,
                        cLQd11bVoiceMaxAdmBandwidth,
                        cLQd11bVoiceMaxRoamBandwidth,
                        cLQd11bVideoAdmCtrlSupport,
                        cLQd11bVideoMaxAdmBandwidth,
                        cLQd11bVideoMaxRoamBandwidth,
                        cLQd11bGprProbeInterval
                    }
    STATUS          current
    DESCRIPTION
        "This collection of objects represents the
        quality-of-service parameters 802.11b networks."
    ::= { ciscoLwappQosMIBGroups 2 }

ciscoLwappQosDot11WlanConfigGroup OBJECT-GROUP
    OBJECTS         { cLQd11GprSupport }
    STATUS          current
    DESCRIPTION
        "This collection of objects represents the
        quality-of-services parameters on a particular WLAN."
    ::= { ciscoLwappQosMIBGroups 3 }

ciscoLwappQosDot11CacStatsGroup OBJECT-GROUP
    OBJECTS         {
                        cLQd11CacVoiceBwInUse,
                        cLQd11CacVideoBwInUse,
                        cLQd11CacVoiceCallsInProgress,
                        cLQd11CacRoamVoiceCallsInProg,
                        cLQd11CacTotalVoiceCallsAP,
                        cLQd11CacTotalRoamCallsAP,
                        cLQd11CacVoiceCallsRejectedAP,
                        cLQd11CacRoamCallsRejectedAP,
                        cLQd11CacRejCallsInsufBw,
                        cLQd11CacRejCallsBadParams,
                        cLQd11CacRejCallsPhyRate,
                        cLQd11CacRejCallsQosPolicy
                    }
    STATUS          current
    DESCRIPTION
        "This collection of objects provide the call
        admission control statistics observed on the
        dot11 interfaces of an AP."
    ::= { ciscoLwappQosMIBGroups 4 }

ciscoLwappQosDot11aConfigGroupSup1 OBJECT-GROUP
    OBJECTS         {
                        cLQd11aVoiceCtrl,
                        cLQd11aExpeditedBw
                    }
    STATUS          current
    DESCRIPTION
        "This collection of objects represents the
        quality-of-service parameters 802.11a networks."
    ::= { ciscoLwappQosMIBGroups 5 }

ciscoLwappQosDot11bConfigGroupSup1 OBJECT-GROUP
    OBJECTS         {
                        cLQd11bVoiceCtrl,
                        cLQd11bExpeditedBw
                    }
    STATUS          current
    DESCRIPTION
        "This collection of objects represents the
        quality-of-service parameters 802.11b networks."
    ::= { ciscoLwappQosMIBGroups 6 }

END