Created documentation for the Duco component

components/duco.rst

@@ -0,0 +1,210 @@
+Duco Ventilation
+================
+
+.. seo::
+    :description: Instructions for controlling a Duco ventilation system with ESPHome.
+    :keywords: Duco, Ventilation, Connectivity Module
+
+The Duco component allows you to operate a Duco ventilation system using ESPHome, without a need for the Duco Connectivity Board. This will directly communicate with the Duco ventilation system, through a UART connection.
+
+Connecting to the ventilation system
+------------------------------------
+
+This component is able to communicate directly ventilation system. You only need to connect it to a UART bus on your ESPHome device.
+
+A Duco ventilation system such as the DucoBox Energy Comfort D325 has a 12-pin connector that is easily reachable on the PCB. This has the following pinout:
+
+.. image:: ../images/duco-pinout.jpg
+
+Pins 8 (RX) and 9 (TX) can be directly connected to the :ref:`UART Component <uart>` component using jumper wires. As a bonus, you can also take either 3.3V or 5V power from the pins to power an ESP32.
+
+The :ref:`UART Component <uart>` must be configured with a baud rate of 57600, 8 data bits, no parity, and 1 stop bit.
+
+Note: this ESPHome module has only been tested on a DucoBox Energy Comfort D325. It does use the same communication protocol as the Duco Connectivity Board.
+
+.. _duco-gettingstarted:
+
+Getting started
+---------------
+
+To discover the available nodes available for the Duco module, the following can be configured:
+
+.. code-block:: yaml
+
+    duco:
+      discovery: {}
+
+This will output all nodes for the Duco module to the logs every minute, for example:
+
+.. code-block:: text
+
+    [00:00:00][I][duco:200]: Discovered nodes:
+    [00:00:00][I][duco:203]:   Node 1: type 17 (BOX)
+    [00:00:00][I][duco:203]:   Node 2: type 8 (UCBAT)
+    [00:00:00][I][duco:203]:   Node 3: type 12 (UCCO2)
+    [00:00:00][I][duco:203]:   Node 4: type 12 (UCCO2)
+    [00:00:00][I][duco:203]:   Node 52: type 18 (SWITCH)
+    [00:00:00][I][duco:203]:   Node 67: type 9 (UC)
+
+This output shows six nodes connected to the Duco box. Some information can be read from them using this module. For example, you can read the ppm-value from the CO2-sensors with the following configuration:
+
+.. code-block:: yaml
+
+    sensor:
+      - platform: duco
+        co2:
+          - address: 3
+            name: "CO2 Bedroom"
+          - address: 4
+            name: "CO2 Livingroom"
+
+Duco Component:
+---------------
+
+The Duco component can be configured as follows:
+
+.. code-block:: yaml
+
+    duco:
+      id: ducobox
+      uart_id: duco_uart
+      discovery:
+        update_interval: "10s"  # Will output the discovered nodes every 10 seconds
+
+This will create a Duco component with discovery enabled, from a specific UART connection.
+
+
+Configuration variables:
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the Duco component.
+- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want to use multiple UART buses.
+- **discovery** (*Optional*): Enables component discovery output.
+    - **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
+      sensor. Set to ``never`` to disable updates. Defaults to ``60s``.
+
+
+Select component:
+-----------------
+
+.. code-block:: yaml
+
+    select:
+      - platform: duco
+        name: "Mode"
+
+The select component allows you to view and change the current mode the Duco ventilation system is operating at. It supports the following modes:
+
++--------+---------------------------------------------+
+| Value  | Description                                 |
++========+=============================================+
+| AUTO   | Automatic flow rate selection               |
++--------+---------------------------------------------+
+| MAN1   | Manual mode 1 for 15 minutes                |
++--------+---------------------------------------------+
+| MAN2   | Manual mode 2 for 15 minutes                |
++--------+---------------------------------------------+
+| MAN3   | Manual mode 3 for 15 minutes                |
++--------+---------------------------------------------+
+| EMPT   | House empty, low flow rate                  |
++--------+---------------------------------------------+
+| CNT1   | Indefinite manual mode 1                    |
++--------+---------------------------------------------+
+| CNT2   | Indefinite manual mode 2                    |
++--------+---------------------------------------------+
+| CNT3   | Indefinite manual mode 3                    |
++--------+---------------------------------------------+
+| MAN1x2 | Manual mode 1 for 30 minutes                |
++--------+---------------------------------------------+
+| MAN2x2 | Manual mode 2 for 30 minutes                |
++--------+---------------------------------------------+
+| MAN3x2 | Manual mode 3 for 30 minutes                |
++--------+---------------------------------------------+
+| MAN1x3 | Manual mode 1 for 45 minutes                |
++--------+---------------------------------------------+
+| MAN2x3 | Manual mode 2 for 45 minutes                |
++--------+---------------------------------------------+
+| MAN3x3 | Manual mode 3 for 45 minutes                |
++--------+---------------------------------------------+
+
+Configuration variables:
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+- **name** (*Required*, string): Name of the select component.
+- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
+  sensor. Set to ``never`` to disable updates. Defaults to ``60s``.
+- All other options from :ref:`config-select`
+
+Text Sensor component:
+----------------------
+
+Read the serial number for the Duco box:
+
+.. code-block:: yaml
+
+    text_sensor:
+      - platform: duco
+        name: "Serial Number"
+
+Configuration variables:
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+- **name** (*Required*, string): Name of the sensor.
+- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
+  sensor. Set to ``never`` to disable updates. Defaults to ``60s``.
+- All other options from :ref:`config-sensor`
+
+Sensor component:
+-----------------
+
+.. code-block:: yaml
+
+    sensor:
+      - platform: duco
+        co2:
+          - address: 3
+            name: "CO2 Bedroom"
+          - address: 4
+            name: "CO2 Livingroom"
+        filter_remaining:
+          name: "Filter Time Remaining"
+        flow_level:
+          name: "Flow Level"
+          update_interval: "5s"
+        time_remaining:
+          name: "Mode Time Remaining"
+          update_interval: "5s"
+
+Configuration variables:
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+- **co2** (*Optional*): One or more CO2 sensors. With the following configuration options:
+    - **address** (*Required*, int): Address of the CO2 sensor.
+    - **name** (*Required*, string): Name of the sensor.
+    - **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
+      sensor. Set to ``never`` to disable updates. Defaults to ``60s``.
+    - All other options from :ref:`config-sensor`
+- **filter_remaining** (*Optional*): Sensor for receiving filter status updates
+    - **name** (*Required*, string): Sensor name
+    - **update_interval** (*Optional*): The interval to check the
+      sensor. Set to ``never`` to disable updates. Defaults to ``60s``.
+    - All other options from :ref:`config-sensor`
+- **flow_level** (*Optional*): Sensor for the flow level
+    - **name** (*Required*, string): Sensor name
+    - **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
+      sensor. Set to ``never`` to disable updates. Defaults to ``60s``.
+    - All other options from :ref:`config-sensor`
+- **time_remaining** (*Optional*): Sensor for the time remaining on the current mode
+    - **name** (*Required*, string): Sensor name
+    - **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
+      sensor. Set to ``never`` to disable updates. Defaults to ``60s``.
+    - All other options from :ref:`config-sensor`
+
+
+
+See Also
+--------
+
+- `Protocol Analysis <https://github.com/kokx/duco-reveng>`__
+- :apiref:`duco/duco.h.h`
+- :ghedit:`Edit`

index.rst

@@ -1028,6 +1028,7 @@ Select Components
     LVGL widget Select, components/select/lvgl, lvgl_c_sel.png
     Modbus Select, components/select/modbus_controller, modbus.png
     Tuya Select, components/select/tuya, tuya.png
+    Duco Ventilation, components/duco, duco.svg
 
 Speaker Components
 ------------------