Daly H/K/M/S-Series BMS integration

components/sensor/daly_bms.rst

@@ -9,6 +9,8 @@ The ``daly_bms`` sensor platform allows you to use a Daly Smart BMS
 (`more info <https://dalyelec.en.made-in-china.com/>`__)
 with ESPHome.
 
+**Be aware**, newer Daly BMS (H/K/M/S-Series) use another protocol based on Modbus, available via the :doc:`/components/sensor/daly_hkms_bms` component.
+
 The BMS communicates via :ref:`UART <uart>`.
 
 .. figure:: images/daly_bms_example.png

components/sensor/daly_hkms_bms.rst

@@ -0,0 +1,226 @@
+Daly H/K/M/S-Series BMS Sensor
+==============================
+
+.. seo::
+    :description: Instructions for setting up a Daly H/K/M/S-Series Smart BMS
+    :image: daly_bms.jpg
+
+The ``daly_hkms_bms`` sensor platform allows you to use a Daly H/K/M/S-Series Smart BMS
+(`more info <https://dalyelec.en.made-in-china.com/>`__)
+with ESPHome.
+
+Older Daly BMS use a custom UART-based protocol available via the :doc:`/components/sensor/daly_bms` component.
+
+.. figure:: images/daly_k-series_bms_example.png
+    :align: center
+    :width: 100.0%
+
+The communication with this component is done via a :ref:`UART <uart>` using a non-standard variation of the :ref:`Modbus protocol <modbus>`,
+either using RS485 or 3.3V UART.
+There may be multiple BMS on a single RS485 bus.
+
+.. code-block:: yaml
+
+    # Example configuration entry
+    uart:
+      - id: bms_uart
+        baud_rate: 9600
+        ...
+
+    modbus:
+      id: bms_modbus
+      uart_id: bms_uart
+
+    daly_hkms_bms:
+      - modbus_id: bms_modbus
+        daly_address: 1
+        update_interval: 10s
+
+
+Configuration variables:
+************************
+
+- **modbus** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`Modbus Component <modbus>` if you want
+  to use multiple Modbus buses.
+- **daly_address** (*Optional*, int): Address to use, defaults to ``1``. Address of the BMS can be set using the DALY PC Software.
+- **update_interval** (*Optional*, :ref:`config-time`): Delay between data requests, defaults to ``30s``.
+
+Sensor
+------
+
+A sensor platform to read BMS data
+
+.. code-block:: yaml
+
+    sensor:
+      - platform: daly_hkms_bms
+        daly_hkms_bms_id: bms_id
+        voltage:
+          name: "Battery Voltage"
+        current:
+          name: "Battery Current"
+        battery_level:
+          name: "Battery Level"
+        remaining_capacity:
+          name: "Remaining Capacity"
+        cycles:
+          name: "Battery Cycles"
+        temperature_mos:
+          name: "Temperature MOS"
+        max_temperature:
+          name: "Temperature Max"
+        min_temperature:
+          name: "Temperature Min"
+        max_cell_voltage:
+          name: "Cell Voltage Max"
+        min_cell_voltage:
+          name: "Cell Voltage Min"
+
+
+Configuration variables:
+************************
+
+- **daly_hkms_bms_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the daly_hkms_bms hub if you want
+  to use multiple BMS.
+
+- **voltage** (*Optional*): Voltage of the battery pack connected to Daly BMS.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **current** (*Optional*): Current flowing trough the BMS (input or output from batttery).
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **battery_level** (*Optional*): Battery level in % (SoC).
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **remaining_capacity** (*Optional*): The capacity in Ah left in the battery.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **cycles** (*Optional*): The number of charge cycles of the battery.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **temperature_mos** (*Optional*): The BMS MOSFET temperature.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **temperature_board** (*Optional*): The BMS PCB temperature (might not be available on all models).
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **temps_number** (*Optional*): The number of temperature sensors.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **max_temperature** (*Optional*): The higher temperature measured from the temperature sensors.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **max_temperature_probe_number** (*Optional*): The sensor number which has measured the higher temperature.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **min_temperature** (*Optional*): The lower temperature measured from the temperature sensors.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **min_temperature_probe_number** (*Optional*): The sensor number which has measured the lower temperature.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **temperature_1** (*Optional*): The first temperature sensor. There can be up to 8 temperature sensors.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **cells_number** (*Optional*): The number of cells in series in the battery pack.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **max_cell_voltage** (*Optional*): The cell of the battery with the highest voltage.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **max_cell_voltage_number** (*Optional*): The cell number of the battery with the highest voltage.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **min_cell_voltage** (*Optional*): The cell of the battery with the lowest voltage.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **min_cell_voltage_number** (*Optional*): The cell number of the battery with the lowest voltage.
+  All options from :ref:`Sensor <config-sensor>`.
+
+- **cell_1_voltage** (*Optional*): The voltage of cell number 1. Cell number can be from 1 to 48.
+  All options from :ref:`Sensor <config-sensor>`.
+
+Text Sensor
+-----------
+
+Text sensor that indicates the status of BMS.
+
+.. code-block:: yaml
+
+    text_sensor:
+      - platform: daly_hkms_bms
+        status:
+          name: "BMS Status"
+
+Configuration variables:
+************************
+
+- **daly_hkms_bms_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the daly_hkms_bms hub if you want
+  to use multiple BMS.
+
+- **status** (*Optional*): The BMS Status (Charging, Discharging, Stationary).
+  All options from :ref:`Text Sensor <config-text_sensor>`.
+
+Binary Sensor
+-------------
+
+Binary sensor that indicates the status of MOS.
+
+.. code-block:: yaml
+
+    binary_sensor:
+      - platform: daly_hkms_bms
+        charging_mos_enabled:
+          name: "Charging MOS"
+        discharging_mos_enabled:
+          name: "Discharging MOS"
+
+Configuration variables:
+************************
+
+- **daly_hkms_bms_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the daly_hkms_bms hub if you want
+  to use multiple BMS.
+
+- **charging_mos_enabled** (*Optional*): The BMS charging MOS status to enable the recharge of the battery.
+  All options from :ref:`Binary Sensor <config-binary_sensor>`.
+
+- **discharging_mos_enabled** (*Optional*): The BMS discharging mos status to enable the load.
+  All options from :ref:`Binary Sensor <config-binary_sensor>`.
+
+- **precharging_mos_enabled** (*Optional*): The BMS precharging mos status to precharge the load's capacitors.
+  All options from :ref:`Binary Sensor <config-binary_sensor>`.
+
+- **balancing_active** (*Optional*): Whether the BMS is currently balancing the cells.
+  All options from :ref:`Binary Sensor <config-binary_sensor>`.
+
+UART Connection
+---------------
+
+Connect RX from BMS to TX on ESP board and TX from BMS to RX on ESP board.
+
+Alternatively, use an RS485 converter and connect A to A/+ and B to B/-.
+Always connect the ground when using RS485 to avoid stray currents running through the RS485 transceivers.
+
+Be aware that by default, the BMS goes to sleep after 1 hour and can not be woken up via RS485,
+only by RX/TX UART communication, charging/discharging the battery or toggling the switch input.
+
+The connectors are compatible with JST-GH (1.25mm pin pitch).
+
+.. figure:: images/daly_k-series_bms_pinout.png
+    :align: center
+    :width: 100.0%
+
+    UART / RS485 Pinout.
+
+**3.3v Warning:** The UART 3.3v is designed to supply power to the Bluetooth module, not an entire ESP.
+There may be WiFi connection issues (or possibly damage to the BMS) when using this 3.3V rail to power an ESP.
+There is also 12V on the connector which should be able to supply more current.
+
+See Also
+--------
+
+- :ref:`sensor-filters`
+- :doc:`/components/sensor/daly_bms`
+- :ref:`modbus`
+- :apiref:`daly_hkms_bms/daly_hkms_bms.h`
+- :ghedit:`Edit`

index.rst

@@ -419,6 +419,7 @@ Electricity
     CSE7766, components/sensor/cse7766, cse7766.svg, Voltage & Current & Power
     CT Clamp, components/sensor/ct_clamp, ct_clamp.jpg, Alternating Current (AC)
     Daly BMS, components/sensor/daly_bms, daly_bms.jpg, Voltage & Current & Power
+    Daly H/K/M/S-Series BMS, components/sensor/daly_hkms_bms, daly_hkms_bms.png, Voltage & Current & Power
     DSMR, components/sensor/dsmr, dsmr.svg, Electrical counter
     HLW8012, components/sensor/hlw8012, hlw8012.svg, Voltage & Current & Power
     INA219, components/sensor/ina219, ina219.jpg, Direct Current (DC)