Retro-Go is a firmware to play retro games on ESP32-based devices (officially supported are ODROID-GO and MRGC-G32). The project consists of a launcher and half a dozen applications that have been heavily optimized to reduce their cpu, memory, and flash needs without reducing compatibility!
Get started in BUILDING.md
- Nintendo: NES, SNES (slow), Gameboy, Gameboy Color, Game & Watch
- Sega: SG-1000, Master System, Mega Drive / Genesis, Game Gear
- Coleco: Colecovision
- NEC: PC Engine
- Atari: Lynx
- Others: DOOM (including mods!)
- In-game menu
- Favorites and recently played
- GB color palettes, RTC adjust and save
- NES color palettes, PAL roms, NSF support
- More emulators and applications
- Scaling and filtering options
- Better performance and compatibility
- Turbo Speed/Fast forward
- Customizable launcher
- Cover art and save state previews
- Multiple save slots per game
- Wifi file manager
- And more!
- Download
retro-go_1.x_odroid-go.fwfrom the release page and copy it to/odroid/firmwareon your sdcard. - Power up the device while holding down B.
- Select retro-go in the files list and flash it.
- Download
retro-go_1.x_mrgc-g32.fwfrom the release page and copy it to/espgbc/firmwareon your sdcard. - Power up the device while holding down MENU (the volume knob).
- Select retro-go in the files list and flash it.
This method is intended to be used when .fw support isn't available (when porting to a new device) or undesirable (devices with smaller flash).
- (optional) Port retro-go to your device (PORTING.md)
- Build a .img file (refer to Building Retro-Go below)
- Flash the image:
esptool.py write_flash --flash_size detect 0x0 retro-go_*.imgNote: Your particular device may require extra steps (like holding a button during power up), different esptool flags, or modifying base.sdkconfig.
Game covers should be placed in the romart folder at the base of your sd card. You can obtain a pre-made pack here. Retro-Go is also compatible with the older Go-Play romart pack.
You can add missing cover art by creating a PNG image (160x168, 8bit). Two naming schemes are supported:
- Filename-based:
/romart/nes/Super Mario.png(notice the rom extension is not included) - CRC32-based:
/romart/nes/A/ABCDE123.pngwherenesis the same as the rom folder, andABCDE123is the CRC32 of the game (press A -> Properties in the launcher to find it), andAis the first character of the CRC32
Note: CRC32-based, which is what is used in the pre-made pack, is much slower than name-based! This type is useful because filenames vary greatly despite having identical CRCs, but if you generate your own art I suggest you use filename-based format and delete all CRC-based art from your SD Card to improve responsiveness.
Some emulators support loading a BIOS. The files should be placed as follows:
- GB:
/retro-go/bios/gb_bios.bin - GBC:
/retro-go/bios/gbc_bios.bin - FDS:
/retro-go/bios/fds_bios.bin - MSX: In folder
/retro-go/bios/msx/put:MSX.ROMMSX2.ROMMSX2EXT.ROMMSX2P.ROMMSX2PEXT.ROMFMPAC.ROMDISK.ROMMSXDOS2.ROMPAINTER.ROMKANJI.ROM
The roms must be packed with LCD-Game-Shrinker and a tutorial can be found here.
To use wifi you will need to create a /retro-go/config/wifi.json config file. Its content should look like this:
{
"ssid": "my-network",
"password": "my-password"
}Multiple networks can be defined using the following format (then selectable in the Options menu):
{
"ssid0": "my-network",
"password0": "my-password",
"ssid1": "my-network",
"password1": "my-password",
"ssid2": "my-network",
"password2": "my-password"
}Time synchronization happens in the launcher immediately after a successful connection to the network.
This is done via NTP by contacting pool.ntp.org and cannot be disabled at this time.
Timezone can be configured in the launcher's options menu.
You can find the IP of your device in the about menu of retro-go. Then on your PC navigate to http://192.168.x.x/ to access the file manager.
Retro-Go supports the external DAC mod for the ODROID-GO
which allows high quality audio through headphones. You can switch to it in the menu Audio Out: Ext DAC.
Pinout
| GO PIN | PCM5102A PIN |
|---|---|
| 1 | GND |
| 2 | - |
| 3 | LCK |
| 4 | DIN |
| 5 | BCK |
| 6 | VIN |
| 7 | - |
| 8 | - |
| 9 | - |
| 10 | - |
Retro-Go typically detects and resolves application crashes and freezes automatically. However, if you do
get stuck in a boot loop, you can hold DOWN while powering up the device to return to the launcher.
The volume isn't correctly attenuated on the GO, resulting in upper volume levels that are too loud and
lower levels that are distorted due to DAC resolution. A quick way to improve the audio is to cut one
of the speaker wire and add a 33 Ohm (or thereabout) resistor in series. Soldering is better but not
required, twisting the wires tightly will work just fine.
A more involved solution can be seen here.
Alternatively you can use the headphones DAC mod mentioned earlier in this document.
In Retro-Go, save states will provide you with the best and most reliable save experience. That being said, please read on if you need or want SRAM saves. The SRAM format is compatible with VisualBoyAdvance so it may be used to import or export saves.
You can configure automatic SRAM saving in the options menu. A longer delay will reduce stuttering at the cost of losing data when powering down too quickly. Also note that when resuming a game, Retro-Go will give priority to a save state if present.
Instructions moved to THEMING.md.
To build retro-go, refer to BUILDING.md.
- The NES/GBC/SMS emulators and base library were originally from the "Triforce" fork of the official Go-Play firmware by crashoverride, Nemo1984, and many others.
- The design of the launcher was originally inspired/copied from pelle7's go-emu.
- PCE-GO is a fork of HuExpress and pelle7's port was used as reference.
- The Lynx emulator is a port of libretro-handy.
- The SNES emulator is a port of Snes9x 2005.
- The DOOM engine is a port of PrBoom 2.5.0.
- The Genesis emulator is a port of Gwenesis by bzhxx.
- The Game & Watch emulator is a port of lcd-game-emulator by bzhxx.
- The MSX emulator is a port of fMSX by Marat Fayzullin.
- PNG support is provided by lodepng.
- PCE cover art is from Christian_Haitian.
- Some icons from Rokey.
- Background images from es-theme-gbz35.
- Special thanks to RGHandhelds and MyRetroGamecase for sending me a G32 device.
- The ODROID-GO community for encouraging the development of retro-go!
Everything in this project is licensed under the GPLv2 license with the exception of the following components:
- fmsx/components/fmsx (MSX Emulator, custom non-commercial license)
- handy-go/components/handy (Lynx emulator, zlib)